2 (dua) units timba buah sesuai unt

2 (dua) units timba buah sesuai untuk kapasitas 45 ton TBS/jam type dua rantai dipasang dengan kemiringan 80o lengkap dengan corong pemasukan, pengeluaran, bordes kontrol yang sesuai pada bagian atas timba dan penyokong yang diperlukan.
Bagian atas dan bawah fruit elevator terbuat dari m.s. plat tebal 8 mm, bagian dinding terbuat dengan m.s. plat 3 mm dan 4.5 mm. Badan timba dibuat dari m.s. plat tebal 4.5 mm yang dibautkan ke rantai dimana baut dan mur digunakan dari jenis high tensile steel.
Untuk dasar rail pada elevator dipasang besi siku 65 x 65 x 6 mm yang diikat dengan baut pada dinding elevator dan untuk rail dipergunakan besi plat bar 60 x 6 mm.
Fruit elevator dilengkapi dengan penegang rantai yang dipasang pada ujung bawah elevator. Elevator dilengkapi dengan pintu pengontrol yang dipasang pada bahagian bawah.
Konstruksi pada bagian depan badan elevator mempergunakan baut dan mur untuk memudahkan pemeliharaan.
Untuk menumpu kedua sisi poros bahagian atas dipakai plummer block bearing dan
bahagian bawah dipakai take-up bearing.
Rantai timba buah type extended pin dengan breaking load 32.000 lbs, chain wheel dengan pitch 150 mm lengkap dengan roller chain & sprocket. Elevator digerakkan oleh gear motor dengan data sebagai berikut :
- Daya : 11 kw.

결과 (영어) 1:

2 (two) units of a Dipper capacity suitable for fruit 45 tons FFB/hour type two chains mounted with the slope of the intake funnel with 80o, spending, bordes the corresponding control on the top of the Dipper and proponents are required.The top and bottom of the fruit surface is made of 8 mm thick m.s. plate, the wall is made with m.s. plate 3 mm and 4.5 mm. Body Dipper made from thick plate m.s. 4.5 mm dibautkan to the chain in which the bolt and nut used of high tensile steel.For the base rail on elevators installed iron elbow 65 x 65 x 6 mm bolts fastened with the wall rail used for elevators and iron plate bars 60 x 6 mm.Fruit elevators equipped with penegang chains are mounted at the lower end of the elevators. Elevators are equipped with door controllers are mounted on the bottom.Construction on the front of the elevators using the bolt and nut for easy maintenance. To focus both sides of the top of the shaft is worn plummer block bearings and the bottom of the worn bearing take-up.The chain extended pin type fruit Dipper with breaking load 32,000 lbs, chain wheel with 150 mm pitch complete with roller chain & sprocket. The elevator is driven by gear motor with the following data: -Power: 11 kw.

결과 (영어) 2:

2 (two) units bucket of fruit according to the capacity of 45 ton TBS / hour type two chains fitted with 80o slope complete with funnel income, expenditure, landing the appropriate control on the top of the bucket and the proponent is required.
The top and bottom of the fruit elevator is made ​​of ms 8 mm thick plate, part of the walls are made ​​with ms plate 3 mm and 4.5 mm. Agency ms dipper made ​​of 4.5 mm thick plate is bolted to a chain where the bolts and nuts are used on the type of high tensile steel.
For the basic rail in an elevator mounted angle iron 65 x 65 x 6 mm are fastened with screws on the wall of the elevator and rail used for iron plate bar 60 x 6 mm.
Fruit elevators equipped with tensioning chain mounted on the lower end of the elevator. Elevator equipped with a door controller mounted on the bottom portion.
Construction on the front of the body using bolts and nuts elevators for easy maintenance.
To rivet on both sides of the shaft portion is used plummer block bearing and
the bottom portion is used take-up bearing.
Chain type bucket fruit extended pin with a breaking load of 32,000 lbs, chain wheel with 150 mm pitch complete with roller chain and sprockets. Elevator driven by a gear motor with the following data:
- Power: 11 kw.